← Back to the configurator
Brand guide · Wajer 55 HT · Hull 55178
ZARPADO logo: a curling wave mark followed by the name ZARPADO in Wajer lettering

One wave, five distinct shapes, always in motion. Zarpar means to set sail, zarpado means over the top, outstanding. The logo carries both: a wave standing out and always in motion.

Mark
Five shapes, rounded tips, one drawing for every size
Name
Drawn in the Wajer lettering
Colour
One colour at a time: Serpentine Green, Pegasus Grey or Waterline Red
Version
2.2 · official · 19 Oct 2026
The mark

One wave, five shapes, one colour

The big curl, its crest band, the inner curl, the upper tail with its outer line, and the lower tail are five separate shapes. Each one is thickest in its middle and narrows toward its ends, and every end is rounded. At the crest the three tips step back one after the other: the lip reaches lowest, the crest band stops a little higher, the inner curl sits higher and further back. The white lines between the shapes open up toward the middle and narrow at the ends.

The mark in Serpentine Green on Pegasus Grey
Serpentine GreenThe default, on Pegasus Grey or white.
Pegasus GreyThe light version, on Serpentine Green or other dark grounds.
The mark in Waterline Red on Pegasus Grey
Waterline RedFor accents, on Pegasus Grey or white only.
5separate shapes, one fill each
42anchor points in the whole mark
+30%how much wider each white line is at its middle than at its ends
1colour per logo, never mixed
Sizes

One drawing for every size

The mark is drawn to hold up small: open white lines, rounded tips and no hairlines. Below it, the mark as your browser renders it at real pixel widths. It reads from about 40 px and is clean from 48 px. Use 48 px as the smallest size on screen.

Width
16 px
24 px
32 px
48 px
64 px
96 px
Serpentine
Red
Lockups

Mark and name

The name is drawn in the lettering of the Wajer brand: wide, squared capitals with rounded corners and generous spacing, so the boat's name sits naturally next to its builder's. Use the lockups exactly as drawn, in one colour; never re-set the name in a font.

Horizontal lockup in Serpentine Green
Horizontal, primaryHull side, documents. Name height is 34% of the mark's height; the gap is 22% of the mark's height.
Stacked lockup in Serpentine Green
StackedFor small website headers, square formats, flags, merchandise. The name spans 1.8 times the mark's width, with the wave close above it.
ZARPADO wordmark in Wajer lettering
Name aloneWhen the mark already appears nearby, such as the stern steps under a flag.
Horizontal lockup in Waterline Red on Pegasus Grey
Colour

Three colours, taken from the boat

The logo is always one colour: the hull's Serpentine Green, the hardtop's Pegasus Grey, or the red of the waterline. Screen values are exact. Pantone references are the nearest Pantone C (coated) matches for print, and RAL references are for paint and signage; proof both against the real paint. Paint targets are given in CIELAB (D65) as lightness L*, chroma C* and hue h, the values a paint lab measures.

HEX
#1E3544
RGB
30 53 68
CMYK
56 22 0 73
Pantone
7546 C (ΔE 1.8)
RAL
620-M metallic (ΔE 3.1)
CIELAB
L* 21.0 · C* 12.8 · h 252°
Paint
Awlcraft SE Serpentine Green MCL54556, metallic, toned down to about 20% less chroma
Pegasus Grey
HEX
#EDE7DB
RGB
237 231 219
CMYK
0 3 8 7
Pantone
9226 C (ΔE 1.3)
RAL
9001 Cream (ΔE 2.0)
CIELAB
L* 91.8 · C* 6.5 · h 90°
Paint
Wajer Pegasus Grey OL1131 (Awlgrip)
Waterline Red
HEX
#E72512
RGB
231 37 18
CMYK
0 84 92 9
Pantone
485 C (ΔE 3.0)
RAL
3028 Pure Red
CIELAB
L* 49.9 · C* 90.8 · h 40°
Paint
RAL 3028 Pure Red, solid (not metallic)
Logo colour on backgroundContrastUse
Serpentine on Pegasus Grey10.3 : 1The default pairing. Everything.
Serpentine on white12.7 : 1Everything.
Pegasus Grey on Serpentine10.3 : 1Everything on dark grounds: flags, crew wear, the hull in Serpentine.
Red on Pegasus Grey or white3.7–4.5 : 1Accents and larger uses: 96 px or 15 mm and up.
Red on Serpentine2.8 : 1Avoid: too little contrast.
Space & size

Room to breathe, and how small it can go

Keep a clear zone of x on every side, where x is a quarter of the mark's height. Nothing else enters that zone: no text, edges or other logos. That includes the edges of bars and headers: in the website header the stacked lockup sits centred, with at least x above and below it.

xxxx Mark with its clear zone
ArtworkScreenPrintEmbroideryCut vinyl
Mark≥ 48 px≥ 12 mm≥ 45 mm≥ 110 mm
Horizontal lockup≥ 220 px wide≥ 40 mm wide≥ 120 mm wide≥ 300 mm wide
Stacked lockup≥ 100 px wide≥ 20 mm wide≥ 60 mm wide≥ 150 mm wide

Sizes are the artwork's width. They follow from the narrowest white line (about 2.9% of the mark's width) and the smallest gap each medium can hold: about 1 px on screen, 0.3 mm in print, 1.3 mm in thread and 3 mm in vinyl. Below a lockup's minimum, use the mark alone.

In use

On the water and off it

Mockups for scale and placement. The cap carries the mark in Serpentine thread; the burgee carries it in Pegasus Grey.

Off-white cap embroidered with the mark
Cap, mark in thread
Serpentine burgee with the mark in Pegasus Grey
Burgee, Pegasus Grey on Serpentine
Files

Artwork

All artwork is vector, with one fill per shape and a transparent background, in the three colours (-serpentine, -pegasus, -red). SVG is for screens and design software; PDF is for print shops, embroiderers and sign makers.

Download all artwork (.zip)

Misuse

Please don't

Mark with two colours
Don'tUse two colours in one logo.
Mark in an off-brand colour
Don'tUse any colour other than Serpentine Green, Pegasus Grey or Waterline Red.
Don'tPut the red logo on Serpentine Green.
Mark stretched horizontally
Don'tStretch, squash, skew or rotate it.
Mark with a drop shadow
Don'tAdd shadows, glows, bevels or outlines.
Mark with the name in a different typeface
Don'tSet the name in any other lettering, or rearrange the lockup.